#Intel Centrino N 6300 Drivers And Applications#

Intel Centrino N 6300 Drivers And Applications

Intel Centrino Ultimate-N 6300 support 112. The SP59207 software installs drivers and applications for Intel Centrino Bluetooth but according to Device Manager this laptop uses a Bluetooth Broadcom 20702.Gentoo Forums :: View topic - Intel Centrino Ultimate-N 6300 TroublesClosed. Currently, Intel does not provide a Windows 10 driver for the Intel Centrino Ultimate-N 6300, and we are not able to confirm if there will be one in the future.

Any ideas?Last edited by jyoung on Mon 7:00 pm edited 1 time in totalFor a point of comparison I booted off an ubuntu live CD and got the same results. Lspci detects the device, and lsmod confirms that the module is loaded. Basically I followed the instructions on : I recompiled my kernel, installed the firmware, loaded the iwlagn module, but no luck.

Iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds iwlagn: Copyright(c) 2003-2009 Intel Corporation iwlagn 0000:06:00.0: PCI INT A -> Link -> GSI 21 (level, low) -> IRQ 21 iwlagn 0000:06:00.0: setting latency timer to 64 iwlagn 0000:06:00.0: Detected Intel Wireless WiFi Link 6000 Series 3x3 AGN REV=0x74 iwlagn 0000:06:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels iwlagn 0000:06:00.0: irq 30 for MSI/MSI-X phy0: Selected rate control algorithm 'iwl-agn-rs' iwlagn 0000:06:00.0: firmware: requesting iwlwifi-6000-3.ucode iwlagn 0000:06:00.0: iwlwifi-6000-3.ucode firmware file req failed: -2 iwlagn 0000:06:00.0: firmware: requesting iwlwifi-6000-2.ucode iwlagn 0000:06:00.0: iwlwifi-6000-2.ucode firmware file req failed: -2 iwlagn 0000:06:00.0: firmware: requesting iwlwifi-6000-1.ucode iwlagn 0000:06:00.0: iwlwifi-6000-1.ucode firmware file req failed: -2 iwlagn 0000:06:00.0: Could not read microcode: -2That is odd, considering all the ucodes on intel's site for the 6000-series are. Any thoughts here? Why does it need an older version? uvesafb: probe of uvesafb.0 failed with error -22 hda-intel: Codec #1 probe error disabling it. The copy of the microcode that I'm using is iwlwifi-6000-4.ucode. It seems to request iwlwifi-6000-3.ucode, and failing that look for iwlwifi-6000-2.ucode and then iwlwifi-6000-1.ucode. Also, I know for certain that there is a strong wireless signal in the room where I've been working.Does the following show anything interesting?Dmesg reports that I'm having trouble with my firmware (thanks!).

Sadly, the upgrade triggered two snags that are holding me up a bit. It's about 80 degrees in here!'Yeah, you have to upgrade to at least version 2.6.32, since it's the first one to use the *.4 firmwareLinux-2.6.31.y/drivers/net/wireless/iwlwifi/iwl-6000.c:48 /* Highest firmware API version supported */Linux-2.6.32.y/drivers/net/wireless/iwlwifi/iwl-6000.c:The package for gentoo-sources 2.6.31 is not even in Portage anymore, so that's another reason to update - you're not protected against all sorts of exploits that have surfaced recently.If you like using old kernels, 2.6.32 would acutally be a good choice since it should to be supported (at least by the kernel developers) for a few years.Okay, I've upgraded to kernel-2.6.34. I never fetched the ucode manually, just emerged the package.# 'Hmm, sounds like your system froze up.'# 'I don't know why. I have the package net-wireless/iwl6000-ucode version 9.221.4.1 installed, kernel config as follows.

You could try by unkeywording some other versions adding =sys-kernel/gentoo-sources- to /etc/gentoo/package.keywords for 2.6.34-r11 (in case it was fixed in a later patchset) or even 2.6.35-r9.The nice thing about kernels is that it's easy to switch between them - just put several entries in the bootloader, and if one doesn't work right, you reboot and use the other.Last edited by Etal on Thu 2:32 am edited 1 time in totalThat sounds reasonable, I could switch around until I found one that worked. You can try different kernels and see which ones work best. Given that, should I use 2.6.32 instead?That's up to you. My old kernel reported the same error on boot up but kept going.Hi, I just did some searching and found a few threads that report bugs in the 2.6.34-r6 kernel. ' It complains that it can't overwrite /dev/mapper/control. Basically I'll start typing and after some number of keystrokes I'll will stop registering - not even a screen echo.Second, when I boot up repeatedly on the new kernel (twice or more in a row without booting off the old kernel in between) it halts at 'Waiting for uevents to be processed.

You should probably open a separate topic for that. Is there a menuconfig parameter that I should look at?And, one more possible clue: When I plug in an external usb keyboard, the problem persists.What do you mean by portage won't let you? Did you do it by specifying the version?As for the keyboard, I'm afraid I can't help you - I never had that kind of a problem. To test this, I tried to go to releases of 2.6.34 lower than r6 but it wouldn't let me.That aside, I'm starting to wonder if I'm missing something somewhere else. Then, I tried to switch to 2.6.32, and emerge wouldn't let me go back down.